Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
Were you looking for facts on Installing A Bathtub?
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Installing a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is easily easily accessible, the task can relocate quickly; if you have to open up a wall surface to get rid of the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will need an assistant to leave the old tub as well as set in the brand-new one. Make certain you have qualified yourself for the work as well as are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed project, it is far better to take into consideration using one before you start. Opportunities are you might need a specialist plumber to make tube links.
This write-up will aid you install a brand-new bathtub in your bathroom if you have actually already gotten a brand-new tub and don't need to alter the plan of your previous water pipelines.
Your devices as well as material checklist must consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is detach the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of getting rid of the existing taps can be fairly bothersome due to the limited access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the staying water that will come from the pipes. When the supply pipelines have actually been removed, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin ensuring that the washers remain in place between the tap and also the sink. Protect the tap in place with the manufacturer supplied backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap connectors. The previous type needs to be attached to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Utilizing the two wooden boards under its feet, position the tub in the required placement. The wooden boards are practical in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the tub up until the spirit level checks out degree.
To install faucets, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water and check all joints as well as new pipework for leakages as well as tighten them if needed. Fill up the bathtub and likewise examine the overflow outlet and the typical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bathtub should wait until the bath tub has been made use of at the very least once as this will resolve it right into its final setting.
Planning for the Installation
To start with, the sustaining framework supplied with the bath must be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, causing problems with dampness and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, as well as can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill up the tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can split rather early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly readily available on the marketplace. It is suggested to fit the tiles making use of water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Make feedback down below. We will be delighted to hear your opinions about this blog posting. Hoping that you come back again in the near future. I beg you take a moment to share this blog posting if you liked it. Thanks a bunch for your time. Please come by our blog back soon.
Instant fix? Dial! Report this page